一、定时器按钮与显示屏功能
1. 定时器按键与液晶屏显示分布

①　45×10液晶显示屏
②　="启动与确认按钮"
③　▲"停止、变换与功能设置按钮"
④　► "加热定时与启动定时按钮"
⑤　 信号发射标记
⑥　 定时设定标记
2. 定时器基本工作参数
工作温度T：
－40℃＜T≤＋60℃
工作半径R：
电量充足非屏蔽环境下：
10米≥R＞5米（保守范围）
定时器应当在相距加热器主机10米范围内工作。
二、首次安装
驻车加热器控制电路与汽车电瓶由断开状态进行连通视为首次安装。首次安装时，需要在8秒内按一下=、▲、►当中的任意一个按钮，进行自动通讯对码(即"握手"操作)。对码后，加热器控制系统会自动唯一锁定本定时器通讯地址码。对码后换用任何其它定时器无法控制本车加热器，进而实现安全控制。
如果在首次启动的8秒内没有执行对码操作。主机控制系统会自动进行安全锁定。此时，任何定时器无法与主机控制系统进行通讯。必须重新断开主机电路中加热器线路保险（蓝色）并重新连接后再次执行首次安装的通讯对码操作。
三、定时器设置
1. 启动与停止设置
启动：按下="启动与确认"按钮，屏幕显示"START　HOT　10"表示命令主机开始加热10分钟。其中，加热时间可分别设置为10、20、30、40和50分钟。
停止：在屏幕显示当前时钟状态下，短促按动一次▲"停止、变换与功能设置按钮"。屏幕显示"STOP HOT ."主机停止加热。
2. 定时设置
加热时长：在屏幕显示当前时钟状态下，连续按动► "加热定时与启动定时按钮"可在10到50分钟范围内设定加热时长。屏幕显示"HOT TIME"加热时长设定值。
定时启动：在屏幕显示当前时钟状态下，持续按住▲"停止、变换与功能设置按钮"3秒钟。屏幕显示"START SET ?"询问："是否开始设置（定时启动时间）？"此时，按动► "加热定时与启动定时按钮"屏幕依次显示：定时编号、定时状态、定时时间、定时时长。例如："1－－" 表示"定时1 关闭"；"1 ON 08:16 20"分别表示：定时1开启、8点16分启动、加热20分钟。上列显示中始终有一组闪烁的数值，表示当前可设置数值。连续按动► "加热定时与启动定时按钮"闪烁数值可在各组数值间切换。此时，按动▲"停止、变换与功能设置按钮"可根据需要对相应数值进行修改。定时设置开启后屏幕显示 "铃铛"图标表示已设置定时启动。主机将在设定时间自动执行预定时长的加热动作。
3. 时钟设置
在屏幕显示当前时钟状态下，持续按住▲"停止、变换与功能设置按钮"3秒钟。屏幕显示"START SET ?"后，再次按动▲"停止、变换与功能设置按钮"屏幕显示"TIME SET ?"此时，连续按动► "加热定时与启动定时按钮"屏幕闪烁显示当前时钟。并在小时与分钟修改项之间闪烁切换。此时，按动▲"停止、变换与功能设置按钮"可校对修改当前时钟。
4. 屏幕夜光显示
在夜晚或黑暗环境下，持续按住► "加热定时与启动定时按钮"3秒钟，显示屏进入夜光显示状态。此时，只要按动任意按钮，屏幕将保持背光显示状态。并在操作结束后的第5秒自动关闭夜光灯。

注意事项：
1. 本定时器线路板覆有"三防漆"图层。一般情况下，具有一定的防潮、防腐的性能。但使用时应尽量避免人为将饮料、酸液、汽油等浸入定时器机体。以延长机器使用寿命。
2. 避免将定时器置于易挤压按钮的环境中。避免不必要的意外启动耗费燃油。
3. 加热器在不同的环境温度下应当采用不同的加热时长设置。以期达到经济实用的效果。
4. 经常检查定时器电量是否充足。加热器在夏季不使用时，应将定时器内的7号电池取出，避免腐蚀定时器。

A, timer button and display function

1.The timer key and the display on the LCD panel distribution

①　45×10LCD screen

②　="Start and confirmbutton"

③　▲"Stop, transform and functionbutton"

④　►"Heating timing and start timing button"

⑤　Signal emission markers

⑥　Timing Settings markers

2.The timer basic working parameters

Working temperature T：

－40℃＜T≤＋60℃

Working radius R：

Power sufficient the shielding environment：

10m≥R＞5米m（Conservative range）

Timer ought to be in 10 meters apart heater work within the host.

Second, first installed

In car heater control circuit and car battery by disconnect state connected as first installation. First installation, the need for 8 SEC click=、▲、►any of a button, automaticcommunications to code (namely "handshake" operation). To code, heater control system will automatically only locking this timer communications address. To change any other code with timer unable to control this vehicle heater, then realizing safety control.

If the first time you start the 8 seconds to code doesn't perform operation. The main engine control system will be automatically safety lock. At this time, any timer can't communicate with host control system. Have to disconnect host circuits heater lines insurance (blue) and reconnecting again after execution of the first installed in communication operation Code.

Three, timer Settings

1.Start and stop Settings

Activation: press="start with confirmation" button, the screen display "START HOT 10" that the command hosts started heat for 10 minutes. Among them, the heating time can set respectively for 10, 20, 30,40 and 50 minutes.

Stop:In the screen display the current clock condition, short press again▲"stop,transform and functionbutton". Screen shows "STOP HOT." host stop heating.

2.Timing Settings

Heating duration: the screen display the current clock condition, continuous press ► "heating timing and start timing button" can be in 10 to 50 minutes long range set heating. Screen display a "HOT TIME"heating duration value.

Time start-up: the screen display the current clock condition, continue hold▲"stop, transform and functionbutton" 3 seconds. The screen shows "START SET?" ask: "whether to start setting (time start-up time)?" At this point, press the ► "heating timing and start timing button" screen ordinal display: timing Numbers, timing state, regular time, regular duration. For example: "1 --" means "timing 1; shut" "1 ON 08:16 20" seperately: timing 1 open, 8 o 'clock 16 points startup, heating 20 minutes. The above shows throughout a group of flickering numerical, said the current can be set value. Continuous press ► "heating timing and start timing button" twinkle in exp1 numerical values can switch between them. At this point, press the▲"stop, transform and functionbutton" as may be necessary for the corresponding numerical modified. Timing Settings after open screen display"Bell" icon has set time start-up. Host will in time set automatically perform predefined time heating action.

3. Clock Settings

In the screen display the current clock condition, continue hold▲"Stop, transform and functionbutton" 3 seconds. The screen shows "START SET?" Press again,▲"Stop, transform and functionbutton" screen display "TIME SET?" at this time, continuous press ► "heating timing and start timing button" screen flashing display the current clock. And in the hour and minute modify between a twinkleswitching. At this point, press the▲"stop, transform and proofreading functionsettingbutton" can modify the current clock.

4.With night-light display screen

At night or dark environment, continue hold ► "Heating timing and start timing button" 3 seconds, screen into night-light display state. At this time, just press the button, the screen will keep any backlight shows state. And in the operation after the end of the first 5 seconds shut down automatically luminous lamp.

Note:

1. This timer PCB cladding have "three proofing lacquer" layer. Normally, have certain moistureproof and anticorrosive performance. But when using, should avoid people will drink, acid, such as gasoline immersed timer organism. In order to prolong the service life of the machine.

2. Avoid will timer in easy extrusion buttonenvironment. Avoid unnecessary accidents start-up costs fuel.

3. Heater in different environmental temperature should adopt different heating un-ling Settings. In order to achieve economic and practical effect.

4.Often check timer power enough. Heater in summer when not in use, should the timer within 7 battery, avoid corrosion timer.

• button [´bʌtn] n.钮扣 vt.扣上(扣子) (初中英语单词)
• confirm [kən´fə:m] vt.证实；认可；加强 (初中英语单词)
• function [´fʌŋkʃən] n.机能；职责 vi.活动 (初中英语单词)
• working [´wə:kiŋ] a.工人的；劳动的 (初中英语单词)
• circuit [´sə:kit] n.环行 v.(绕....)环行 (初中英语单词)
• system [´sistəm] n.系统，体系，制度 (初中英语单词)
• unable [ʌn´eibəl] a.不能的；无能为力的 (初中英语单词)
• communication [kə,mju:ni´keiʃən] n.通信；通讯联系 (初中英语单词)
• screen [skri:n] n.银幕 vt.遮蔽 (初中英语单词)
• continuous [kən´tinjuəs] a.连续不断的；延长的 (初中英语单词)
• twinkle [´twiŋkl] vi.&n.闪烁；眨眼 (初中英语单词)
• performance [pə´fɔ:məns] n.履行；行为；工作 (初中英语单词)
• achieve [ə´tʃi:v] vt.完成；达到；获得 (初中英语单词)
• transform [træns´fɔ:m] v.转化，转变；改造 (高中英语单词)
• battery [´bætəri] n.炮兵连；炮台；电池 (高中英语单词)
• automatic [,ɔ:tə´mætik] a.自动的 n.自动装置 (高中英语单词)
• communicate [kə´mju:nikeit] vi.通讯；传达；传播 (高中英语单词)
• execution [,eksi´kju:ʃən] n.执行；演奏；表演 (高中英语单词)
• switch [switʃ] n.开关 v.转换 (高中英语单词)
• environment [in´vaiərənmənt] n.郊区；周围；条件 (高中英语单词)
• gasoline [´gæsəli:n] n.汽油 (高中英语单词)
• organism [´ɔ:gənizəm] n.生物体；有机体 (高中英语单词)
• prolong [prə´lɔŋ] vt.延长；拉长；拖延 (高中英语单词)
• automatically [ɔ:tə´mætikli] ad.自动地；无意识地 (英语四级单词)
• vehicle [´vi:ikəl] n.车辆；媒介物 (英语四级单词)
• respectively [ri´spektivli] ad.各自地；分别地 (英语四级单词)
• setting [´setiŋ] n.安装；排字；布景 (英语四级单词)
• corresponding [,kɔri´spɔndiŋ] a.符合的；相当的 (英语四级单词)
• luminous [´lu:minəs] a.发光的；明晰的 (英语四级单词)
• radius [´reidiəs] n.辐射光线；半径范围 (英语六级单词)
• installation [,instə´leiʃən] n.就职；安装；装置 (英语六级单词)
• duration [djuə´reiʃən] n.持久；持续期间 (英语六级单词)
• normally [´nɔ:məli] ad.正常情况下；通常 (英语六级单词)